• GO GREEN
  • EXTERIOR
  • INTERIOR
  • ENAMEL
  • WOOD FINISHES
  • SPECIAL COATING
  • ITALINO
  • INSTA CARE
  • OTHER PRODUCTS
  • HOME
  • COMPANY
  • NEWS AND EVENTS
  • CONTACT
OTHER PRODUCTS
CLEAN

CLEAN EX

Exterior Surface Cleaner

Algae quick kill Solution.This to be applied on existing exterior walls to remove algae, fungus etc. It is preferred to be applied by brushing method.Allow 1 hrs. to dry and Clean with wire brush for easy removing. Dilution 1:1 water

BIOWASH

BIOWASH

Anti-Algal/Fungal Pre Treatment Wash

Biowash is a low toxicity biocide specifically developed for the complete microbiological protection of surfaces which might need disinfecting, prior to painting. Biowash is a water based liquid. This will enhance dry film protection and delay the formation of Fungus, algae etc. Dilution 1:1 water.

AROPRIME INTERIOR

AROPRIME INTERIOR

Synthetic Cement Primer (Water Thinnable) Emulsion Based

Before applications of "AROPRIME" Water Thinnable Synthetic Cement Primer, please ensure that the surface is thoroughly dry. All loose and flaking paints must be removed. Thin two parts of primer with one part of clean water. "AROPRIME" Water Thinnable Synthetic Cement Primer can be applied on Interior surfaces. Allow to airdry overnight before applying Finishing Coats.

AROPRIME EXTERIOR

AROPRIME EXTERIOR

Synthetic Cement Primer

Directions For Use: Ensure that the surface to be painted is free from any loose paint, dust, grease, fungus or algae. Newly plastered surfaces are to be fully cured and dry. Exterior rough surfaces previously coated with lime paint should be wire brushed and washed with water throughly and allowed to dry. Aroprime Exterior Wall Primer is to be thinned with water to obtain brushing consistency by adding primer:water in 1:1(v/v) and is not be over thinned. Apply a single coat liberally using brush and allow drying for 4-6 hours. Apply recommended number of topcoats.

AROLAC INTERIOR

AROLAC

Interior Primer Water Thinnable

Before applications of "AROLAC" Water Thinnable Interior Primer, please ensure that the surface is thoroughly dry. All loose and flaking paints must be removed. Thin two parts of primer with one part of clean water. "AROLAC" Water Thinnable Interior Primer can be applied on Interior surfaces. Allow to airdry overnight before applying Finishing Coats.

AROLAC EXTERIOR

AROLAC

Exterior Wall Primer

Ensure that the surface to be painted is free from any loose paint, dust, grease, fungus or algae. Newly plastered surfaces are to be fully cured and dry. Exterior rough surfaces previously coated with lime paint should be wire brushed and washed with water throughly and allowed to dry. Arolac Exterior Wall Primer is to be thinned with water to obtain brushing consistency by adding primer: water in 1:1(v/v) and is not be over thinned. Apply a single coat liberally using brush and allow drying for 4-6 hours. Apply recommended number of topcoats.

WALL GRACE

WALL GRACE

White Cement Wall Putty

Apollo paints exterior Wall Putty is a specially designed product based on white cement, redispersible polymer and functional additives for filling and leveling surface imperfections on exterior cement plasters and interior surfaces providing a smooth finish for subsequent painting.

POLO

POLO PUTTY

Premium Acrylic Wall Putty

Direction For Use: Stir throughly before use. Add water & stir well if putty is too thick. Surface Treatment: Clean the surface well. Remove all loose matter by sanding with emery paper number 180 and wiping off the powder with a cloth or cotton waste. Apply one coat of Cement Primer (Water Thinnable). After drying for 8 hours sand lightly with emery paper number 320. Application: Apply Polo Wall Putty using putty knife to obtain a smooth and uniform surface. Deep dents should be filled in thin layers. Allow to dry for 4hours and sand with emery paper number 320. The loose powder on the surface is to be wiped off with a cloth or cotton waste. Finally, apply one coat of Cement Primer (Water Thinnable). The surface is ready for application of finish paint.

PRIDE

PRIDE

Premium Acrylic Distemper Emulsion Finish

SURFACE PREPARATION: Clean the surface thoroughly, removing all grease, Oil, Salt, fungus loose flaking particles. Apply Primer and Polo Putty and use sandpaper to smoothen the surface. New plaster should have matured for about three months before painting. FINISHING: "PRIDE" Premium Acrylic Distemper is supplied in paste form. Thin down by adding 1.5 to 2 parts of water to 3 parts of distemper by weight to, obtain correct application consistency. Apply 2 to 3 coats with an interval of 6-8 hours between coats.